Step & Repeat Backdrop
10 ft × 8 ft photo wall on a heavy-duty adjustable stand. Set it up in five minutes, fold it into the carry bag when you're done.
What it is
A step and repeat is the logo wall people stand in front of at your event. Every photo taken there carries your brand — which is why the pattern needs to run edge to edge, since cameras crop in tight.
Ours uses a large-tube frame. Most backdrops on the market run 1″ poles that flex and wobble; these are 1.625″, which is the difference between a wall that stands straight all day and one you keep re-adjusting.
What's in the box
- Printed 10′×8′ fabric graphic, hemmed with 3″ pole pockets
- Adjustable aluminum stand — 4 uprights, 2 crossbars
- Two heavy-weight base plates
- Hex bolts and thumb screws
- Padded carry bag
Good to know
The stand adjusts from 69″–129″ wide and 36″–102″ tall, so it outlives any single graphic. Buy it once, then reorder just the fabric at $249 for your next event.
Graphic
| Finished size | 120″ W × 96″ H (10 ft × 8 ft) |
| Material | 9 oz dye-sublimated wrinkle-free fabric |
| Finish | Low sheen — no flash glare |
| Print sides | Single-sided (back is plain white) |
| Edges | Hemmed all round |
| Pole pockets | 3″ sewn, top and bottom |
Hardware
| Tube diameter | 1.625″ aluminum (competitors use 1″) |
| Width range | 69″ – 129″ |
| Height range | 36″ – 102″ |
| Locking | Plastic locking collars |
| Base | Two heavy-weight foot plates |
| Carry bag | Included |
Turnaround
| Digital proof | 2–4 hours after ordering |
| Production | Ships next business day after you approve |
| Shipping | Free FedEx Ground shipping from CA, TX or PA |
| Typical total | 3 business days door to door |
Free design template
Print-ready PDF at the exact 120″ × 96″ size with trim, safe zone and the pole pockets already marked, so nothing important gets swallowed by a hem.
File requirements
- PDF or JPEG, single page
- CMYK — no Pantone or spot colors
- 150 dpi at final size
- Fonts converted to outlines
- No crop marks and no bleed
Design tips that matter
- Cover the whole panel — photos crop tighter than you expect
- Stagger the rows. A straight grid reads as wallpaper; offset reads as a brand wall
- Logos around 6–10″ tall photograph best
- Keep logos out of the 3″ pole pockets — the hem seam shows there
- Mid-tone backgrounds beat pure white under a camera flash
No designer? No problem.
Send us a logo — even a screenshot — and we'll build the repeat pattern for you and email a proof. There's no design fee, ever.
About five minutes with two people. Everything you need is in the bag.
Join the two top poles at the B–B ends, then the bottom poles C–D. Extend the telescoping ends to your width.
Drop each upright into the socket on a base plate, then thread the hex bolt up from underneath and hand-tighten.
Slide the top and bottom crossbars through the 3″ pole pockets on the graphic.
Lift onto the uprights and lock with the black thumb screws. Raise the height until the fabric pulls taut.
Taking it down
Reverse the order and fold the graphic loosely rather than creasing it. Let it dry fully if it got damp — fabric packed wet will mildew.
Can the stand hold a different size backdrop?
Is it printed on both sides?
Will it wrinkle in the bag?
Will camera flash glare off it?
What are the pole pockets and do they affect my design?
Can I use it outdoors?
How fast will I get it?
How do I clean it?
Can I get a size other than 10×8?
Didn't find it? See the covering every product, or read our — all custom print sales are final, which is why we proof first.